Smart Pill Reminder · منبه الدواء الذكي

Parts Catalog

Every part in the build, with real photos from the shop or of your own parts, what it does in the machine, and what to check when it arrives.

Parts
26
From the two shops
JD 17.82 or JD 13.82 without optional items
From other shops
7
Prices and stock
all in stock, checked 7 Nov 2026

Found while matching the photos to the design

In the machine

12

The boards and parts that get built in. "Guide part" is the number in the build guide's Inside section.

ESP32 on its prototype board, 38-pin, micro-USB, on a 57.2 × 56.3 mm board
You have itGuide part 8

ESP32 on its prototype board 38-pin, micro-USB, on a 57.2 × 56.3 mm board

1Already built

The brain. It runs the clock, the motor, the voice and the phone app over Wi-Fi. Its green prototype board also carries the power bus (a 5 V row and a GND row). It sits on the bottom plate, USB end against the back wall.

Check The bottom plate's holder is drawn for exactly this board: 57.2 × 56.3 mm, with the ESP32 (48.3 × 25.4 mm) raised 2.5 mm on its headers. It rests on ledges and clips under 4 snap posts, and its USB socket lines up with the 16 × 12 mm service opening. A different ESP32 or board size (like the shop's USB-C version) would need the holder redrawn.

Photos: your own board

Stepper motor + driver, 28BYJ-48 5 V with ULN2003 board
On your listGuide part 2 and 10

Stepper motor + driver 28BYJ-48 5 V with ULN2003 board

1 × JD 3.00Future Electronics

Turns the carousel one slot per dose. The motor hangs under the deck with its shaft in the carousel's D-hole. The driver board sits on the bottom plate.

Check The motor's white plug goes into the board's socket. The driver board (34.8 × 32.1 mm) screws onto 4 posts on the bottom plate with M2.5 × 6 self-tapping screws, LEDs to the front.

Shop pagePhotos: Future Electronics

Mini limit switch, with lever, C / NO / NC
On your listGuide part 3 and 7

Mini limit switch with lever, C / NO / NC

2 × JD 0.35Future Electronics

Two of the same switch. HOME clicks once per carousel turn so it can find slot H. FULL-TILT clicks when the cup is tipped all the way, which tells the machine the pills are out.

Check Your list had one: buy two. The slots are drawn for your switch as measured: M2 screw holes 6.5 mm apart and a lever reaching 2.3 mm past the body. Wire C (common) and NO (normally open).

Shop pagePhotos: Future Electronics

DFPlayer Mini, MP3 player module
On your listGuide part 9

DFPlayer Mini MP3 player module

1 × JD 1.75Future Electronics

Plays the Arabic and English voice files from the microSD card and drives the speaker directly.

Check It sits on a printed U-shaped stand between its two pin rows and clips in at the end away from the card. Put the microSD card in before you press it down.

Shop pagePhotos: Future Electronics

Speaker, 3 W, 4 Ω, 40 mm
On your listGuide part 4

Speaker 3 W, 4 Ω, 40 mm

1 × JD 1.25Mikroelectron

The voice of the alarm. It presses into the ring under the grille on the top left.

Check The shop's photos show the "4Ω 3W" label and the 40 mm size, as in the design. Keep the volume at 25 or lower. On sale at JD 1.25 (normally JD 2.00).

Shop pagePhotos: Mikroelectron

LCD 1602 with I2C, 16 × 2 characters, blue backlight
On your listGuide part 5

LCD 1602 with I2C 16 × 2 characters, blue backlight

1 × JD 2.50Future Electronics

Shows the time, the doses left and messages like TAKE YOUR PILLS!. It screws into the sloped front window.

Check The window is drawn for your board as measured: screw holes 75.1 × 31.1 mm apart, window 72.3 mm wide. Its holes are 3.0 mm, so it takes M2.5 screws, not M3. Bend the I2C board's 4 pins straight back before fitting it, because the left wall is close. Its I2C address is 0x27 or 0x3F; the code finds it on its own.

Shop pagePhotos: Future Electronics

Clock module, DS3231 with AT24C32 memory
On your listGuide part 11

Clock module DS3231 with AT24C32 memory

1 × JD 3.50Mikroelectron

Keeps the time while the machine is switched off, so the dose times stay right after a power cut without opening the app. It stands in two rails at the front left of the bottom plate.

Check The shop sells it without a battery and lists a rechargeable LIR2032, but yours holds a plain CR2032 (second photo). Wire VCC to the ESP32's 3V3 pin, not 5 V, and remove the tiny resistor marked 201 next to the glass diode (first photo, top right) so the CR2032 is never charged. Its address is 0x68; the board is 38.6 × 23 mm.

Shop pagePhotos: your own module

Rocker switch KCD1-101, red, 2-pin, 6 A 250 V
You have itGuide part 12

Rocker switch KCD1-101 red, 2-pin, 6 A 250 V

1Already bought

ON/OFF. It snaps down into the deck, left of the lid.

Check Its cutout is its body plus 0.2 mm a side, and the deck round it is thinned so the side clips can grip: both come from your sizes on the measuring sheet. Check it in the FitTest print first.

Shop pagePhotos: your own switch

USB-C power socket, snap-in, 2 wires
You have itGuide part 13

USB-C power socket snap-in, 2 wires

1Already bought

Power comes in here, through the back wall. The red wire goes to the power switch, the black one to the GND row.

Check It clicks into a rectangular hole from outside: two springy latches catch behind the wall, which is thinned round the hole so they can grip. No glue. The hole comes from your sizes on the measuring sheet. Yours has no LED.

Photos: your own socket

Male header pins, 40-pin strip, 2.54 mm
Add to your orderGuide part 8

Male header pins 40-pin strip, 2.54 mm

1 × JD 0.05Future Electronics

The power bus: break off two strips of 6 and solder them onto the ESP32's prototype board, one row for 5 V and one for GND, so the modules can share the ESP32's single 5 V pin.

Check One strip is plenty.

Shop pagePhotos: Future Electronics

Electrolytic capacitor, 1000 µF / 25 V
Add to your orderGuide part 8

Electrolytic capacitor 1000 µF / 25 V

1 × from JD 0.15Future Electronics

Smooths the current spikes from the speaker amplifier and Wi-Fi so the ESP32 doesn't restart in the middle of an alarm. It goes across the 5 V and GND rows.

Check The listing has many values: pick 1000 µF / 25 V (470 µF / 25 V also works). The long leg is +, to 5 V.

Shop pagePhotos: Future Electronics

microSD card, 32 GB or smaller
Another shopGuide part 9

microSD card 32 GB or smaller

1Not at Future Electronics

Holds the voice files for the DFPlayer.

Check Format it as FAT32. Future Electronics doesn't sell cards; any phone or computer shop has them.

Example photo: Afrank99, CC BY-SA 3.0, Wikimedia Commons

Wiring and power

5
Jumper wires, 20 cm, female–female, pack of 20
On your list

Jumper wires 20 cm, female–female, pack of 20

2 × JD 0.45Future Electronics

All the connections between the boards.

Check There are about 27 connections (4 of them for the clock module), so get 2 packs. The switches and the speaker have solder tabs: cut the plug off one end and solder it.

Shop pagePhotos: Future Electronics

Resistor 1 kΩ, carbon film, ¼ W
Add to your order

Resistor 1 kΩ carbon film, ¼ W

1 × from JD 0.02Future Electronics

Goes in the wire from ESP32 GPIO17 to DFPlayer RX. It stops a hissing noise.

Check Pick 1 kΩ in the list. Its colour bands are brown, black, red.

Shop pagePhotos: Future Electronics

Heat-shrink tube kit, 3–8 mm
Add to your orderOptional

Heat-shrink tube kit 3–8 mm

1 × JD 2.00Future Electronics

Covers the soldered joints on the power switch and the resistor.

Check Optional: electrical tape does the same job.

Shop pagePhotos: Future Electronics

USB charger, 5 V, 2 A
Add to your orderOptional

USB charger 5 V, 2 A

1 × JD 1.00Future Electronics

Powers the machine. A laptop USB port is too weak when the motor and speaker run.

Check Skip it if you have a phone charger marked 5V 2A or more. Some power banks switch off when the machine draws little current, so use a wall charger at the fair.

Shop pagePhotos: Future Electronics

USB cable, USB-A to USB-C, 1 m
Add to your orderOptional

USB cable USB-A to USB-C, 1 m

1 × JD 1.00Future Electronics

Runs from the charger to the USB-C socket on the back.

Check Skip it if you have one.

Shop pagePhotos: Future Electronics

Screws and nuts

2

Future Electronics doesn't sell these. A small M2 / M2.5 / M3 screw-and-nut box from a hardware shop covers everything.

M3 countersunk screws, M3 × 10 and M3 × 8
Another shopGuide part 2

M3 countersunk screws M3 × 10 and M3 × 8

2 × M3 × 10 + 2 nuts, 4 × M3 × 8Not at Future Electronics

The two M3 × 10 hold the motor ears, screwed down from the top of the deck so the heads sit flat; add 2 M3 nuts underneath. The four M3 × 8 hold the bottom plate in the corner posts and cut their own thread.

Check Countersunk means the head is a cone that sits flush. The photo shows M3 × 8.

Example photo: 4300streetcar, CC BY 4.0, Wikimedia Commons

M2.5 and M2 screws, pan head with nuts, plus self-tapping
Another shopGuide part 3, 5, 7 and 10

M2.5 and M2 screws pan head with nuts, plus self-tapping

4 × M2.5 × 12 + nuts, 4 × M2.5 × 6 self-tapping, 4 × M2 × 12 + nutsNot at Future Electronics

Four M2.5 × 12 with nuts hold the LCD from the front. Four M2.5 × 6 self-tapping screws hold the ULN2003 driver board on its posts. Four M2 × 12 with nuts hold the two limit switches in their slots.

Check The LCD's holes are 3.0 mm, too tight for M3. The second photo is the kind of assortment box that has all of these.

Example photos: Kazuhisa Otsubo, CC BY 2.0; Herusutimbul, CC BY-SA 4.0, Wikimedia Commons

Materials

4

The five printed parts (base, bottom plate, carousel, cup and lid frame) aren't in this catalog: they have no real photos until they're printed. The build guide shows them in CAD.

PLA filament, about 0.5 kg
Another shop

PLA filament about 0.5 kg

1 spoolNot at Future Electronics

For the five printed parts on the Bambu X1.

Check Print the carousel and cup in white or a light colour so the pills are easy to see. The lid frame can be any colour.

Example photo: Gary C Martin, CC BY 2.0, Wikimedia Commons

Clear acrylic, laser cut, 3 mm
Another shop

Clear acrylic, laser cut 3 mm

1 pieceNot at Future Electronics

The lid window, 153.4 × 154.6 mm, so you can see which slots are full.

Check Take cad/laser/lid_acrylic.svg (or the .dxf) to a laser-cutting shop: red lines are cut, black are engraved. Keep the protective film on until you glue it.

Example photo: Felipe Sanches, CC BY-SA 2.0, Wikimedia Commons

Clear two-part epoxy, or clear silicone
Another shop

Clear two-part epoxy or clear silicone

1 small packNot at Future Electronics

Glues the acrylic window into the lid frame.

Check Don't use superglue: its fumes leave a white haze on clear acrylic.

Example photo: Taktoa, CC BY-SA 3.0, Wikimedia Commons

Hot glue, glue gun and sticks
Another shop

Hot glue glue gun and sticks

a few sticksNot at Future Electronics

Holds the speaker in its ring. Everything else clips, clicks or screws in.

Check A small glue gun is enough.

Example photo: Evan-Amos, public domain, Wikimedia Commons

Not needed

3
TCRT5000 IR sensor, reflective sensor module
Not needed

TCRT5000 IR sensor reflective sensor module

1 × JD 1.00Future Electronics

It was on the first list, to see pills in the cup. The second limit switch does that job better, so it isn't used.

Check Don't buy it for this build. If you already have it, keep it as a spare.

Shop pagePhotos: Future Electronics

Double-sided tape, clear, 28 mm
Not needed

Double-sided tape clear, 28 mm

1 × JD 1.00Future Electronics

It was meant to hold the boards in corner stops. The boards now clip into printed holders (ledges with snap posts, a stand, screw posts and rails), so no tape is needed.

Check Don't buy it for this build.

Shop pagePhotos: Future Electronics

Prototype board, 4 × 6 cm, double-sided
Not needed

Prototype board 4 × 6 cm, double-sided

1 × JD 0.35Future Electronics

It was meant for a separate power-bus board. The power bus now goes on the ESP32's own prototype board, so there is no second board.

Check Don't buy it for this build. It is also too small to carry the ESP32: yours is 57.2 × 56.3 mm.

Shop pagePhotos: Future Electronics

Shopping list

Prices in Jordanian dinars from the shop pages on 7 Nov 2026. The resistor and capacitor listings let you pick a value; their price is the listing's starting price.

PartShopQtyEachTotal
Stepper motor + driver 28BYJ-48 5 V with ULN2003 boardFuture Electronics13.003.00
Mini limit switch with lever, C / NO / NCFuture Electronics20.350.70
DFPlayer Mini MP3 player moduleFuture Electronics11.751.75
Speaker 3 W, 4 Ω, 40 mmMikroelectron11.251.25
LCD 1602 with I2C 16 × 2 characters, blue backlightFuture Electronics12.502.50
Clock module DS3231 with AT24C32 memoryMikroelectron13.503.50
Male header pins 40-pin strip, 2.54 mmFuture Electronics10.050.05
Electrolytic capacitor 1000 µF / 25 VFuture Electronics1from 0.150.15
Jumper wires 20 cm, female–female, pack of 20Future Electronics20.450.90
Resistor 1 kΩ carbon film, ¼ WFuture Electronics1from 0.020.02
Heat-shrink tube kit 3–8 mm OptionalFuture Electronics12.002.00
USB charger 5 V, 2 A OptionalFuture Electronics11.001.00
USB cable USB-A to USB-C, 1 m OptionalFuture Electronics11.001.00
Everything from the two shops17.82
Without the optional items13.82

From other shops

Shop photos belong to Future Electronics Jordan and Mikroelectron and are shown here for reviewing the parts. Example photos are from Wikimedia Commons under the licence named on each card. Cards marked "your own" show your own parts.