Smart Pill Reminder
Everything it takes to build one, with how many of each and a picture of every item: the boards and switches, the wires, each screw and nut by size, the printed parts and the materials.
Everything that gets built in. "Guide part" is the part's number in the build guide.
38-pin, micro-USB, on a 57.2 × 56.3 mm board
The brain.
28BYJ-48 5 V with ULN2003 board
Turns the carousel one slot per dose.
with lever, C / NO / NC
Two of the same switch.
MP3 player module
Plays the Arabic and English voice files from the microSD card and drives the speaker directly.
3 W, 4 Ω, 40 mm
The voice of the alarm.
16 × 2 characters, blue backlight
Shows the time, the doses left and messages like TAKE YOUR PILLS!.
DS3231 with AT24C32 memory
Keeps the time while the machine is switched off, so the dose times stay right after a power cut without opening the app.
red, 2-pin, 6 A 250 V
ON/OFF.
snap-in, 2 wires
Power comes in here, through the back wall.
40-pin strip, 2.54 mm
The power bus: break off two strips of 6 and solder them onto the ESP32's prototype board, one row for 5 V and one for GND, so the modules can share the ESP32's single 5 V pin.
1000 µF / 25 V
Smooths the current spikes from the speaker amplifier and Wi-Fi so the ESP32 doesn't restart in the middle of an alarm.
32 GB or smaller
Holds the voice files for the DFPlayer.
20 cm, female–female, pack of 20
All the connections between the boards.
carbon film, ¼ W
Goes in the wire from ESP32 GPIO17 to DFPlayer RX.
3–8 mm
Covers the soldered joints on the power switch and the resistor.
5 V, 2 A
Powers the machine.
USB-A to USB-C, 1 m
Runs from the charger to the USB-C socket on the back.
Drawn to scale. Every one is in the 3D model, in its hole; the viewer's Screws and nuts buttons show where. A small M2 / M2.5 / M3 screw-and-nut box from a hardware shop covers them all.
M3 thread, 10 mm long, countersunk, 90°
M3 thread, 8 mm long, countersunk, 90°
M2.5 thread, 12 mm long, pan head
M2.5 thread, 6 mm long, pan head
M2 thread, 12 mm long, pan head
5.5 mm across the flats, 2.4 mm thick
5 mm across the flats, 2 mm thick
4 mm across the flats, 1.6 mm thick
Print times and PLA weights of each colour plate, sliced in Bambu Studio (X1 Carbon, 0.4 mm nozzle, 0.20 mm Standard, Bambu PLA Basic, Textured PEI plate). Print the small FitTest first: 40 min and 14 g.
6 h 19 min, 268 g of PLA
The box: deck, walls, the cup bay and every holder.
1 h 55 min, 84 g of PLA
Bottom plate: the boards clip onto it, 4 screws hold it on.
1 h 46 min, 79 g of PLA, together with the cup
Turns on the motor shaft: 15 slots, 14 for doses and 1 empty home slot.
1 h 24 min, 53 g of PLA
Frame for the acrylic window, on 4 pegs.
1 h 46 min, 79 g of PLA, together with the carousel
Catches the pills and tips them into your hand.
about 0.5 kg
For the five printed parts on the Bambu X1.
3 mm
The lid window, 153.4 × 154.6 mm, so you can see which slots are full.
or clear silicone
Glues the acrylic window into the lid frame.
glue gun and sticks
Holds the speaker in its ring.
On the original list but not used in this design. Keep them as spares.
reflective sensor module
It was on the first list, to see pills in the cup.
clear, 28 mm
It was meant to hold the boards in corner stops.
4 × 6 cm, double-sided
It was meant for a separate power-bus board.
Status chips: "You have it" is already yours, "On your list" and "Add to your order" are at Future Electronics or Mikroelectron, "Another shop" means a hardware or general shop. Shop photos belong to Future Electronics Jordan and Mikroelectron; example photos are from Wikimedia Commons (credits in the parts catalog). Printed parts are CAD renders.