Smart Pill Reminderمنبه الدواء الذكي
ESP3215-slot carouselArabic voice alertPhone appESP32قرص من ١٥ خانةتنبيه صوتي بالعربيةتطبيق على الهاتف

Smart Pill Reminderمنبه الدواء الذكي

An 8th-grade science-fair project: a rectangular pill dispenser run by an ESP32. At each dose time a 15-slot carousel turns one slot and drops the pills into a cup. A voice says «حان موعد الدواء» and keeps repeating until the cup is pushed all the way over and the pills slide into your hand.

مشروع لمعرض العلوم في الصف الثامن: موزّع أدوية مستطيل تشغّله لوحة ESP32. في كل موعد يدور قرص من ١٥ خانة خانةً واحدة فتسقط الجرعة في الكوب، ويقول الصوت «حان موعد الدواء» ويستمر بالتذكير حتى يُدفع الكوب إلى نهايته فتنزلق الحبوب إلى اليد.

This site gathers everything made so far: the 3D model, the build guide, the parts lists, the leaflets, and the files to print, laser-cut and program it.

يجمع هذا الموقع كل ما صُنع حتى الآن: النموذج ثلاثي الأبعاد، ودليل البناء، وقوائم القطع، والنشرات، والملفات اللازمة للطباعة والقص بالليزر والبرمجة.

Designed and sliced: 5 plates, about 12 h 4 min and 497 g of PLA. Not printed or powered on yet.التصميم والتقطيع جاهزان: ٥ ألواح، نحو ١٢ س ٤ د و٤٩٧ غ من PLA. لم يُطبع ولم يُشغَّل بعد.

The Smart Pill Reminder: a teal box with an LCD and a red power switch, an octagonal clear lid over the white 15-slot carousel, and the cup in the front opening

Project pagesصفحات المشروع

3D modelالنموذج ثلاثي الأبعاد

Spin the assembled machine and show or hide every part.

أدِر الجهاز المجمّع، وأظهر أي قطعة أو أخفِها.

Build guideدليل البناء

How it works, parts, wiring, assembly, programming and testing, step by step.

طريقة العمل والقطع والتوصيل والتجميع والبرمجة والاختبار، خطوة بخطوة.

Print section out of dateقسم الطباعة قديم

Printالطباعة

5 ready-to-print files, one per filament colour, for the Bambu Lab X1 Carbon.

٥ ملفات جاهزة للطباعة، ملف لكل لون خيط، لطابعة Bambu Lab X1 Carbon.

Filesالملفات

Print files, 3D parts, the laser file, the CAD design, the firmware and the voice files.

ملفات الطباعة، والقطع ثلاثية الأبعاد، وملف الليزر، وتصميم CAD، والبرنامج، وملفات الصوت.

Bill of materialsقائمة المواد

Every part, screw and nut, with counts and pictures.

كل قطعة وبرغي وصامولة، مع العدد والصور.

Print times out of dateأوقات الطباعة قديمة

Parts catalogكتالوج القطع

Where each part was bought, with prices.

من أين اشتُريت كل قطعة، مع الأسعار.

Part sizesمقاسات القطع

The sizes measured on the real parts, which the 3D model uses. It lives on claude.ai and opens only for people it is shared with.

المقاسات التي أُخذت من القطع الحقيقية، ويستخدمها النموذج ثلاثي الأبعاد. الصفحة على claude.ai، ولا تفتح إلا لمن شوركت معه.

opens on claude.aiتفتح على claude.ai

User leafletدليل المستخدم

The folded guide that comes with the device: setup, daily use and help.

الدليل المطوي الذي يأتي مع الجهاز: الإعداد والاستخدام اليومي والمساعدة.

Read before you buildاقرأ قبل البناء

Open issues found so far. None of them is fixed yet.

مشكلات وُجدت حتى الآن، ولم يُصلح أيٌّ منها بعد.

Old print times in the build guide and BOMأوقات طباعة قديمة في دليل البناء وقائمة المواد

The build guide's Print section and the BOM still give the earlier print times, and the guide says no part needs supports. The Print page has the current files: the Base now needs tree supports under the hand opening's ceiling and the LCD window's lower edge.

ما زال قسم الطباعة في دليل البناء وقائمة المواد يعرضان أوقات الطباعة السابقة، ويقول الدليل إن القطع لا تحتاج إلى دعامات. الملفات الحالية في صفحة الطباعة: القاعدة تحتاج الآن إلى دعامات شجرية تحت سقف فتحة اليد والحافة السفلى لنافذة الشاشة.

Wiring photos and firmware pins differصور التوصيل لا تطابق أرقام المنافذ في البرنامج

In the photos of the wired ESP32, a 4-wire plug sits on GPIO 14, 27, 26 and 25, with one more wire on GPIO 32. The firmware's config.h drives the motor driver from GPIO 25, 26, 32 and 33. Move the wires or change PIN_IN1 to PIN_IN4 before you power it up.

في صور لوحة ESP32 الموصولة، القابس ذو الأسلاك الأربعة على المنافذ GPIO 14 و27 و26 و25، وسلك آخر على GPIO 32. أما الملف config.h في البرنامج فيشغّل المحرك من GPIO 25 و26 و32 و33. انقل الأسلاك أو غيّر PIN_IN1 إلى PIN_IN4 قبل تشغيل الجهاز.

photosGPIO 14, 27, 26, 25 (4-wire plug) + GPIO 32config.hGPIO 25, 26, 32, 33 (PIN_IN1 to PIN_IN4)

One LCD nut touches the I2C boardصامولة في الشاشة تلمس لوحة I2C

In the 3D model, one of the nuts that hold the LCD overlaps the LCD's I2C board by about 0.9 mm. Check it when you fit the LCD.

في النموذج ثلاثي الأبعاد، تتداخل إحدى الصواميل التي تثبّت الشاشة مع لوحة I2C الخاصة بها بنحو ٠٫٩ مم. تحقّق من ذلك عند تركيب الشاشة.

Not built yetلم يُبنَ بعد

Nothing has been printed or powered on so far. Print times and PLA weights are Bambu Studio's estimates.

لم يُطبع شيء ولم يُشغَّل الجهاز حتى الآن. أوقات الطباعة وأوزان PLA تقديرات من برنامج Bambu Studio.

Picturesصور